Guitars Upgrade Tremmory S

the idea is nice , but the 3 size offered are simply too long for many floyds , a shorter piston wold suffice .I took small and is ok (still touches claw if you bend up a lot ) . i can NOT see how medium or large size ( longer piston ) would go in any guitar.. piston would bee too long right away.
Installation is very hard ( I DISSASSEMBLE my FLoyds since decades so i know what i say) .Cause is very difficult to catch end of the spring wither way , they should at least prepare one side already ready to be connected , i scratched my tremolo block , so tight..and i'm a muscular guy _
it works "partially" , you go out of tune if you go drop D but slightly so ok for live use , not for recording. Bendings get lot easier and similar in feeling ("halfway feeling") to the hardtail bridges . It also slighltly change tone of strings , but not in a bad/good way ,justt little different -if you disengage with the provided thumbscrew ,the sound get back as before .
It does noise /resistance even in the piston (not picked by the amp) cause the tremolo block and the claw are not in same "line " ( adjusting action put away from same line cause normal springs have their own line different from the tremmory,thouse piston has a not perfect straight insert action) .
As it has those little drawbacks i think is too expensive ,would be more right to be in the 70/ 80 € price than 110€ as is sold , in my opinion .

When they arrived, I had all 3 installed in less than couple of hours, I think. First up was my Strat. Once I had floated the trem (for the first time ever since I bought it), I also realized it was unusable floating as it would not return to tune. If you pushed down and released, it stayed a bit flat. If you then pulled up and released, it would usually come back to tune. The Tremmory comes in 3 different sizes and I ordered the Small size for all 3 guitars as even the small size was too big for the way my guitars were currently setup but I knew I’d be changing all that for the Tremmory anyway. The small size is 71mm and the instructions say to make sure you have at least 3-5mm more than that available. For my Strat this meant taking it from 5 springs decked, all the way down to 2 springs so that I could get a little bit of float and still have enough room between the spring claw and the trem block. Once I had it all set up and in tune, installing the Tremmory was a breeze. Loosen the thumb screw, put some included small felt adhesive pads on the spring claw and the trem block to prevent any extraneous noise from the Tremmory butting against either part, then install it where the middle spring would go, check tuning once again just to be sure and tighten down that thumbscrew. Once I did that, the trem returned to perfect tune every time, double stops stayed in tune, and I go to drop D tuning as well! I couldn’t believe it! I knew this type of unit would stiffen up the trem but I was actually really pleasantly surprised at how much less stiff it was than I was expecting. Still totally usable and way less stiff than when I had it decked. I didn’t do an A/B comparison, but I am guessing that I probably lost the slight tone and sustain benefits I had from having it decked (even better if you have it completely blocked) but this seems like a great compromise of both worlds. I was very impressed with the results.

Next up was the St. Vincent HH. On this one I only had to go down to 3 springs to get a little float and enough room for the Tremmory. The rest of the experience was the same as the Strat.

My JTV-69 was the trickiest. Even down to only 2 springs, I could not keep any real amount of float and still have room for the Tremmory. Through trial and error and very fine tuning, I eventually got the trem just barely against the body but not too stiffly, with just barely enough room to get the Tremmory in there. If I had screwed the claw in any more (to make more room for the Tremmory) then the trem would have been quite solidly on the body again, and if I’m just totally decking the trem, then the Tremmory becomes fairly useless. It would at the very least allow you to deck it without as much spring force and therefore keep the trem a little more usable, but that’s probably not worth $105.

It should also be noted that with the default thumbscrew on the Tremmory, you will need to leave your back plate off. Not a big deal to me. You can loosen that screw if you want a fully floating normal feeling trem for any reason or for a certain songs. Contrarily, you can replace the thumbscrew with an included Allen screw which would allow you to put the back plate back on. I was tempted to do that as I don’t ever intend to loosen it, but I left the thumbscrew for now just so it’s easy enough to loosen in case I find the need to do any adjustments. They also recommend changing strings one by one which I don’t want to do as I like to give my fretboard a good cleaning when I take off all the strings, so I’ll need to block the trem by putting something under it when I take all the strings off as I don’t think the Tremmory could hold it’s place with all the strings off or I’m guessing I could loosen that screw then tighten it back up once I’m re-strung and back up to tune.

It also comes with an extra, stiffer internal spring you can use to replace the default one if you for some reason need or prefer more stiffness from the Tremmory, though the instructions are unclear as to why you would need that other than “preference.”

All in all, my first impressions are quite impressive. The packaging was very high quality and the whole thing from the design to the extra included options seem very well thought out. As far as options for having a slightly stiffer floating trem but with better tuning, and solid double stops and drop D tuning, this seems like the best, easiest, most convenient option out there to me.

I bought the Tremmory so I can do double stop bends without the top note going out of tune while still having the option of using the tremolo traditionally.

Installation was moderately easy on my Fender Player Strat with an ABM tremolo. I replaced the original springs because I wanted noiseless ones (I got the ones from Harley Benton) and I ended up with 3 (2 hard tension and 1 normal tension) after setting the tremolo to my preferred position which is almost decked with very little upwards play just so the tremolo doesn’t hit the body when it returns to its initial position.
2 small black felt pads are provided to acoustically dampen the contact points between the Tremmory the tremolo claw and the tremolo block but they are trash and easily disintegrate so I ended up not using them. They didn’t make a difference in reducing unwanted noise for me anyways.
You do need to apply quite a lot of force to the Tremmory springs to get them in place in both ends and they are pretty hard to grab. I used a needle to pull the end spring into the tremolo block hole. If you’re not handy you will probably have a hard time installing it but it’s certainly possible.

Performance wise, it works in doing what I wanted. Tighten it and you have a faux decked tremolo that doesn’t lift with bends. Untighten and you have normal action tremolo. I’ve read reviews that state that you can still use the tremolo while tightened but I’d say it’s way too stiff in that mode it needs a lot of force to go down and the strings will go out of tune. But if you leave the back panel off at all times it’s really easy to access and tighten or untighten the screw. You can even do it mid-song.

However the Tremmory is very noisy. Even with the felt pads. While tightened it’s almost silent but while untightened it will introduce a distortion like rattle in the guitar’s acoustic sound in most notes and chords. This rattle does not translate through the amp hopefully. But yeah your Strat’s acoustic tone will be destroyed if you care about that…

All in all it seems like a good easy to install and non intrusive accessory!

NOTE
You will most likely need to buy the S (small) because the others are way too big.